Hydronic Air-Water Heat Pump Beretta HYDRO UNIT M 016 Single Phase R-32 20191957

Energy efficiency

• Energy class in heating at 35° C: A+++
• Energy class in heating at 55° C: A++
• COP heating with water set at 35°C: 4.50
• COP heating with water set at 45°C: 3.50
• COP heating with water set at 55°C: 2.85
• EER cooling with water set at 7°C: 3.61
• EER cooling with water set at 18°C: 2.50

Electrical Data

• Power (V,Hz, Ø): 220~240/50/1
• Refrigerant gas: R32

Dimensions and weight

• Dimensions (LxHxD): 1385x945x526 mm
• Empty weight: 144.0 kg

Hydronic Air-Water Monobloc Inverter Heat Pumps Beretta HYDRO UNIT M

These units are used for both heating and cooling applications and for domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, high efficiency low temperature radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase heating capacity in cold outdoor temperatures. The backup heater also serves as a backup in the event of a malfunction and as protection from freezing external water pipes during the winter.

Efficiency and sustainability

The HYDRO UNIT M series heat pumps use R32 as a refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, the reduced loading volumes, the lower CO2 emissions and the increase in energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental.

Silence

The low noise level is guaranteed by the construction measures used and can be further reduced thanks to the silent mode programming, available to the customer

Antifreeze function

The HYDRO UNIT M heat pump is designed for outdoor installation and equipped with the ANTIFREEZE function to protect the entire hydraulic circuit. This customer-programmable function is automatically activated whenever the water temperature in the system drops below a preset value, ensuring the protection of the entire system

Better performance

The ten available models offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee the A+++ energy class up to 35°C and A++ up to 55°C

HP KEYMARK certification

The design meets the requirements of the HP KEYMARK voluntary European certification

Easy and flexible

Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monoblock and contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to quickly respond to the real needs of the environments to be served

Functional elements Beretta Hydro Unit M

Inverter control board Maximizes power under critical load conditions and provides stability and efficiency at partial loads

AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency

Control board Operating parameters constantly analyzes the room temperature and the water temperature to activate the different components and satisfy the needs

Hydronic module Including low consumption circulator, expansion tank, automatic vent valve and safety valve

Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation

Twin rotary compressor The Inverter System design including the DC twin rotary compressor, fan motor and pump ensures precise control of the motor speed for the right power needed to perfectly match the actual load and save energy

Fan Special design of the blade and its edge which allows to optimize the flow surface improving efficiency and reducing fan noise

Heat exchange coil With extended surface and aluminum fins

Install multiple Hydro Unit M

HYDRO UNIT M offers the possibility of connecting up to six units together for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed

Easily manage the system

Advanced remote control

This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to:

• Manage up to six units connected in cascade
• Activate the programmed functions such as the Antifreeze function and the Holiday function, for the peace of mind of the family

REC10MH management module

Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and multilingual menu

USB

Each HYDRO UNIT M is equipped with a USB port to which you can connect USB flash memory to update the unit's firmware

Product Warranty: All products on sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.